Common Types & Uses of Reducing Flanges

 

What is a Reducing Flange?

When there is a change in pipe size, reducing flanges are used. The dominant flange (dimensions) corresponds to the larger pipe size (NPT), but has a smaller diameter to correspond to the smaller pipe size (NPT). These flanges are often available in blind, slip-on, threaded, and weld neck configurations.

 

They are available in all pressure classes and are an excellent choice for joining two different sizes of pipe. This style of flange should not be utilised where a rapid change, such as at a pump, might cause undesirable turbulence.

 

Ablaze Lining is one of the leading Lined Reducing Flange manufacturers in Vadodara.




Uses of Reducing Flanges:

■     In pipe-to-pipe connections, reducing flanges are employed.

■     Reducing flanges are easier to install than non-reducing flanges.

■     When you need to connect different sized flanges, they are the best choice.

■     These flanges are available in a variety of materials and pressures.

■     Welding, glueing, or clamping flanges of similar dimensions with various connecting components secures reducing flanges.

■     They provide the simplest and least expensive means of joining two flanges of differing sizes.

 

Ablaze Lining is a noted Lined Reducing Flange manufacturer in Ahmedabad.

Type of Reducing flanges:

Except for the bore and hub measurements, the flange will have the larger pipe size parameters. Reducing flanges are often available in one of three configurations:

■     Welding Neck flange

■     Slip-On flange

■     Threaded flange

 

The most important aspect of reducing flanges is that they offer a low-cost solution to connect pipes of different sizes.

 

Ablaze Lining is a distinguished Lined Reducing Flange supplier in Gujarat.

■     Weld Neck and Slip-On:

Complete the welding procedure by connecting the flange sides that correspond to the larger diameter of the pipe. Repeat the welding process on the other side of the reducing flange for the lower pipe size. The reduction procedure has now joined both diameters of pipes. Take the required steps to ensure that the inside diameters of the pipes on both sides are appropriately aligned with the Flange's ID.

■     Threaded Flange:

To begin, thread any one size of pipe to one side of the flange. Assemble the pipe so that it reaches the desired depth inside the flange. Repeat the operation with the opposite size of pipe.

 

■     Welding is done on the outside of the pipe after threading to strengthen the strength of the connection in high pressure and temperature situations.

 

If you are looking for the best Lined Reducing Flange distributor in Vadodara, Ablaze Lining is the name you can count on. Contact Today.

Comments

Post a Comment

Popular posts from this blog

Performance, Pressure, Temperature, and Chemistry of PTFE Lined Pipes

Image
  This part aims to give the engineer a foundational understanding of fluoropolymers. Few engineers, in our experience, are exposed to these materials enough in their working careers to comprehend the considerations that must be taken in equipment specification, design, installation, and operation. Metals standards will be specified, weld test procedures will be documented, and materials certification will be required in a typical lined equipment specification. However, the specification is frequently found inadequate when it comes to the fluoropolymer aspect, with only a fleeting mention of PTFE or Teflon being made at best. Performance: The lined pipework and fittings must have the highest performance level as the fundamental element of a fluoropolymer lined process. Plants may be multi-purposed, the equipment can be reused with certainty, and process safety is maximised. Other elements, such as pumps, valves, tanks, and columns, invariably have performance characteristics outsid
Read more

Did You Know this earlier about Line-Reducing Flanges?

Image
There are wafer-type PTFE lined reducing flanges available along with threaded bolt holes and concentric bores. A custom-made solution can be developed for all the transitions lying between the nominal widths as per the client’s needs. PTFE Lined Reducing Flanges can be supplied along with the Anti-static liners to avoid static build-up within pipes on installation. While we offer a wide range of sizes, we specialise in non-standard sizes. Ablaze Lining is the excellent as well as the most proficient Lined Pipe manufacturer in Vadodara . The paper and pulp industry, oil and gas industry, refinery and petrochemical industry, pharmaceutical industry, chemical industry, power generation facilities, and many more uses lined reduction flanges. There is a wide variety of lined reducing flanges available in the market. Popular lined reducing flanges include PTFE lined reducing flanges, PFA lined reducing flanges, FEP lined reducing flanges, and plenty of other things. What is a Reduci
Read more

What is Lined Reducing Flange?

Image
  Available in different sizes and dimensions, Lined Reducing Flange are used for pipe to pipe connections and for connecting flanges of different sizes. Use of Lined Reducing Flange is popular as it is simple to use, easy to install, offers dimensional accuracy , designed with superior strength, serviceability and water resistance ability. Pipes of different dimensions can be easily connected to Lined Reducing Flange. Carbon steel or stainless steel is used for the housing of this flange. The usual range of is Lined Reducing Flange 25 NB – 1000 NB. Drilling on Lined Reducing Flange can be done as per project requirement. Ablaze Polymer, Lining & Coating is a Lined Reducing Flange supplier in Vadodara . Lined Reducing Flange is used in many industries such as pharma industry , paper and pulp industry , petrochemical and refinery industry , oil and gas industry , power generation plants , chemical industry and so on. Ablaze Polymer, Lining & Coating is a Lined Reducing Fl
Read more